Nuevo XTi 2 (Segunda Generacion)

XTi

There's no debate – when you choose Crown's XTi 2 Series, you're choosing one of the most powerful and innovative amplifiers on the market today. That's because the all-new XTi 2 Series amps continue to set the standard for unmatched performance and value, delivering the goods night after night without breaking a sweat.

Next generation features:

• Peak_x Plus™ Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release
• Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning
• 3 User-defined fan mode controls – normal, early and fullspeed – for matching fan performance to a specific application
• New system monitoring provides software visibility of AC line voltage and power supply temperature
• Integrated cast-aluminum handles for easy handling and enhanced durability
• Locking power cord clip provides a secure connection between the amplifier and power cord
• Updated HiQnet Band Manager™ and System Architect™ control software
• Increased number of presets to a total of 30; 29 of which are user definable

 

Input EQ:

6 parametric filters per channel with adjustable Q, ±15 dB boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ section can be bypassed.

Crossover Filters:

Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes ± 15 dB bandpass gain and polarity control.

Output EQ:

8 parametric filters per channel with adjustable Q, ±15 dB boost/cut. This 8-filter EQ section can be bypassed.

Delay:

For signal alignment of driver; 50 mS of total delay.

SubHarmonic Synth:

Takes the low-frequency content of the input signal and "synthesizes" a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect. New: Users now have control over frequency, gain, and filter type.

Peakx™ Plus Limiter:

User defeatable limiter that allows users to control Threshold, Attack, and Release times.

Presets

30 total presets, 29 of which are user-definable.

Sensitivity (for full rated power at 4 ohms):

1.4 Vrms

Frequency Response (at 1 watt, 20 Hz - 20 kHz):

+0 dB, –1 dB

Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms):

XTi1002/2002/4002: 100 dB (A weighted)

XTi6002: 103 dB (A weighted)

Total Harmonic Distortion (THD):

< 0.5%

Damping Factor 20 Hz to 1 kHz:

> 500

Crosstalk (below rated power):

20 kHz - 1 kHz: > 70 db

Input Impedance (nominal):

20k ohms balanced, 10k ohms unbalanced

Maximum Input Signal:

+22 dBu typical

AC Line Voltage and Frequency Configurations:

100 VAC, 120 VAC, 220-240 VAC 50/60 Hz

AC Line Current (120 VAC amplifier playing 1/8 power pink noise into 4 ohms per ch):

XTi1002: 6.8A; no more than 38W at idle

XTi2002: 8.3A; no more than 38W at idle

XTi4002: 10.5A; no more than 38W at idle

XTi6002: 15.3A; no more than 180W at idle

Operating Temperature:

0°C to 40°C at 95% relative humidity (non-condensing)

 

 

Level:

Two front-panel rotary level controls, one for each channel

Power Switch:

On/Off switch applies AC power to the amplifier

Sel/Prev/Next Buttons:

Three buttons near the LCD screen that are used to access menu items and front panel lockout

LCD Screen:

Backlit liquid crystal display that shows preset and processing status

Signal Indicator:

Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs).

–10 Indicator:

Green LED flashes when output signal exceeds -10 dB below clip.

–20 Indicator:

Green LED flashes when output signal level exceeds -20 dB below clip.

Ready Indicator:

Green LED, one per channel, illuminates when the amplifier is ready to produce audio.

Clip Indicator:

Red LED, one per channel, turns on at the threshold of audible distortion

Temp Indicator:

Red LED, one per channel, illuminates under excessive temperature conditions

Power Indicator:

Blue LED illuminates when the amplifier has been turned on and has power

Input Connectors:

XLR, one per channel

Link/Out Connector:

Loop-thru signal from input connector for linking another amplifier, one per channel.

Output Connectors:

Two Neutrik® Speakon® NL4MP output connectors. Channel-1 Speakon® is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon® connectors).

HiQnet™ USB Connector:

Type B, connects to HiQnet™ network.

 

Chassis:

Steel

Front Panel:

Cast-aluminum

Cooling

Proportional speed fan with front-to-rear airflow.

Dimensions:

XTi 1002/2002/4002: 19" (W) x 3.5" (H) x 12.25" (D)

XTi 6002: 19" (W) x 3.5" (H) x 16.2" (D)

Net Weight:

XTi 1002/2002/4002: 18.5 lbs (8.4kg)

XTi 6002: 24.0 lbs (10.9kg)

Shipping Weight:

XTi 1002/2002/4002: 21.5 lbs (9.8kg)

XTi 6002: 30.0 lbs (13.6kg)